UAS4G5G LTE · DOCUMENTATION
Everything you need to get started.
Current guides for the v23 program: installation, cameras, flight control, connectivity, licensing and updates.
Radxa ROCK 4D
Radxa ZERO 3W / 3E
Follow the setup in order.
Still choosing hardware? Check the supported boards first. Then follow these six steps.
Choose the SD card
Check capacity, reliability and the card reader.
Download the right image
Match the image to your Raspberry or Radxa board.
Write and verify
Flash the card, validate it and safely eject it.
Make the first connection
Boot the board, join its network and open UAS.
Try or activate
Choose the included trial or enter your license.
Check your workspace
Check the Dashboard before configuring equipment.
The complete guide library.
Choose reliable storage.
A clean image and a dependable card are the foundation of a stable companion computer.
Read the guide ↗Start hereDownload and test.
Choose your board family. Each image includes the program and its trial entry point.
Read the guide ↗Start hereWrite the system image.
Install the correct board image once. Continue with normal updates from inside the program.
Read the guide ↗Start hereYour first connection.
From a prepared SD card to the activation screen, then into your flight workspace.
Read the guide ↗Start hereTry it. Make it yours.
Start the included 15-minute trial or activate your board permanently with a local UAS license.
Read the guide ↗Start hereKnow your workspace.
Every program tab explained with numbered screenshots, practical steps and the differences between Raspberry Pi and Radxa.
Read the guide ↗HardwareChoose your platform.
One familiar workspace across Raspberry Pi, Radxa ROCK 4D and Radxa ZERO 3W/3E. Camera processing follows the capabilities of each board.
Read the guide ↗HardwareBuilt for Raspberry Pi.
A common Raspberry interface, with camera pipelines adapted to the model rather than a single encoding assumption.
Read the guide ↗HardwareBuilt for Radxa.
ROCK 4D and ZERO 3W/3E bring hardware H.264 and H.265 processing to the same flight workspace.
Read the guide ↗Cameras & videoChoose the right camera path.
USB, Raspberry CSI, HDMI capture and DJI Pocket are distinct inputs. Select the workflow that matches your equipment.
Read the guide ↗Cameras & videoYour first video stream.
Set the source, codec, bitrate and destination in a predictable order.
Read the guide ↗Cameras & videoRaspberry CSI cameras.
Use the Raspberry camera interface with a compatible sensor, cable and image configuration.
Read the guide ↗Cameras & videoCapture an HDMI source.
On Raspberry, a supported HDMI-to-CSI adapter provides the input path for an HDMI-output camera.
Read the guide ↗Cameras & videoUSB cameras, automatically configured.
Detect a compatible source, choose the stream settings and send video to the browser or a ground station.
Read the guide ↗Cameras & videoA second USB camera.
Operate Radxa USB Camera-2 independently, with its own settings and video destination.
Read the guide ↗Cameras & videoDJI Pocket 1 & DJI Pocket 2.
A dedicated live view with gimbal controls, camera settings and board-specific H.264/H.265 streaming.
Read the guide ↗Cameras & videoNetwork camera compatibility.
Confirm the stream protocol and receiver path before choosing an Ethernet or Wi-Fi camera for this release.
Read the guide ↗Cameras & videoMultiple cameras. Separate streams.
Keep camera controls and network endpoints distinct, while respecting the board’s available processing and USB connections.
Read the guide ↗Cameras & videoKeep the picture current.
Tune video for the link you actually have: stable motion, manageable bandwidth and minimal accumulated delay.
Read the guide ↗Flight & telemetryConnect the flight controller.
Detect a compatible ArduPlane controller, view telemetry and route MAVLink to up to three ground stations.
Read the guide ↗Flight & telemetryCockpit, clearly explained.
Raspberry and Radxa camera controls, live view, HUD, map and flight-controller tools.
Read the guide ↗Flight & telemetryMission Planner & GStreamer.
Receive MAVLink telemetry and a matching RTP video stream on your ground computer.
Read the guide ↗Flight & telemetryQGroundControl setup.
Match the telemetry listener and video source to the stream sent by UAS4G5G LTE.
Read the guide ↗Flight & telemetryRelay controls.
Switch external equipment through four channels and confirm the actual reported state.
Read the guide ↗Mobile connectivityMobile connectivity.
USB modem choices for Raspberry Pi and Radxa, with a clear distinction between the existing program workflow and hardware candidates that still need testing.
Read the guide ↗Mobile connectivityHiLink or stick?
Choose the mode that matches the interfaces your modem actually exposes.
Read the guide ↗Mobile connectivityChoose for your network.
LTE and 5G band checklists, named operator examples and regional guidance. Match the exact modem to the network you will use.
Read the guide ↗Mobile connectivityAntennas for a steadier link.
MIMO, positioning, cable losses and practical antenna examples for a dependable UAS cellular uplink.
Read the guide ↗Mobile connectivityBring the modem online.
Choose the correct mode, apply the required provider settings and verify each stage of the connection.
Read the guide ↗Network & VPNConnect locally. Reach it remotely.
Wi-Fi, Ethernet and cellular provide connectivity. Tailscale or ZeroTier provide a reachable network between remote devices.
Read the guide ↗Network & VPNTailscale, step by step.
Connect the board and ground station, authorise access, choose the right addresses and verify video and telemetry.
Read the guide ↗Network & VPNZeroTier, step by step.
Create a private network, join both devices, authorise members and use the assigned IPs for UAS.
Read the guide ↗Program & supportMeet UAS4G5G LTE v23.
The current v23l production builds for Raspberry Pi, ROCK 4D and ZERO 3W/3E, with separate notes for each platform.
Read the guide ↗Program & supportv23 for Raspberry Pi.
Current v23l production build: features, improvements, model-specific camera limits and updates.
Read the guide ↗Program & supportv23 for Radxa.
Current v23l production builds for ROCK 4D and ZERO 3W/3E: cameras, hardware video, trial and updates.
Read the guide ↗Program & supportUpdate from the program.
Apply the signed release package through the Update tab. Normal program updates no longer require rewriting the SD card.
Read the guide ↗Program & supportFind the failed step.
Start with the component that is not working, and preserve the visible status message before changing settings.
Read the guide ↗About EasyDroneDesigned around the aircraft.
UAS4G5G LTE brings video, telemetry, flight controls and connectivity into one browser workspace.
Read the guide ↗ContactLet’s connect.
Licenses, compatibility questions and project enquiries are handled directly. Tell us what you are building.
Read the guide ↗Site informationYour privacy.
How EasyDrone handles website visits, support and license requests, external video, downloads and privacy enquiries. Contact David Iulian.
Read the guide ↗No matching guides.
Try another phrase or choose All guides.